A wrap made of sheer white fabric is a perfect accessory for a dress on a balmy night.  This one was painted with the stencils included in our directions.  Much too big to photograph accurately, we’ve included close up images of details.  The scaled down sketch on the right, which was our original design template, shows the placement of all the elements on the wrap.  The curvy line falls slightly off center in brown.  To the left of it, turquoise with white filigrees, to the right, several filigree images in turquoise against the white background.  To add a little interest, we dusted those same images lightly with brown.  The wrap measures a generous 24”X 72” without the four inch long fringe.

Home    On The Table    Floral Decor    Jewelry    Party Ideas        DIva’s Closet    Home Decor    Computer Creations  Painted   Seasonal Subscribe

CLICK TO SUBSCRIBE & RECEIVE E-MAILS WHEN NEW PROJECTS ARE ADDED TO OUR PAGES

- Painted Projects -

SHEER PAINTED WRAP

FRINGE DIRECTIONS

TIP - We placed a warm iron on one end of the embroidery floss and pulled the entire length slowly under the iron to get all the kinks out. 

  1. 1.Cut the floss into 12” pieces.  An easy and quick way to do that is to tape one edge of the floss to the end of a ruler.  Wrap the floss around vertically. 

  2. 2.Bend the ruler slightly to insert scissors under the floss.  Cut both ends.

  3. 3.Fold a length of floss in half.  Slip it into a large eye needle (#16 embroidery needle).

  4. 4.Pierce the fabric 1/4” from the edge and pull part way through. 

  5. 5.Remove the needle from the floss.

  6. 6.Pull the cut ends through the loop, securing the floss to the hem.   

  7. 7.Use the lines on a standard index card to help you space each fringe 1/4” apart.  Continue adding fringe across the width of the wrap.

  8. 8.To cut the fringe evenly, use painters tape to secure the hemmed edge of the wrap to a cutting surface. Place the tape just above the knotted floss.  Avoid putting the tape on the knotted edges of the floss (like we mistakenly did in the photo) or when you remove it, you may pull out floss along with the tape.  Smooth out the fringe so that the strands are all parallel.  Place a second piece of tape four inches from the hem. 

  9. 9.Using a rotary cutter or a sharp craft knife cut on the four inch edge of the tape.  Remove the tape and your wrap is complete.

step 4

step 6 single filigree

step 7 large filigree

step 8 accent stencil

step 1

step 2

step 4

step 5

step 7

step 6

step 8

SEWING & PAINTING DIRECTIONS

  1. 1.Cut your fabric 74” long by 26” wide.  Hem the long sides first. Instead of measuring and pinning the entire length, baste .50” from the raw edge using a guide on your machine. Fold and press the edge on the basting lne. Turn the pressed edge .50” and sew in place close to the fold.  Remove basting stitch.

  2. 2.Hem the short ends by first pressing a one inch hem, then folding that hem in half.  This will create a half inch hem.

  3. 3.Using the stencil material of your choice, print and cut out the three stencils provided - the large filigree, the single filigree, and the accent stencil.  Keep all the die cut pieces in tact for use later. We used card stock stencils for the filigrees and sprayed the backsides with repositionable adhesive.  The large and small filigree stencils will need to be reversed to create mirror images on one half of the wrap.  If you use stencils that cannot be reversed, you will need to cut out two of each.   

  4. 4.Following our sketch, create one 72” long curved stencil or three 24” pieces that you can piece together.  Because of it’s size, a curve stencil is not included with our instructions.  We used freezer paper for this stencil because it comes in a long roll and can be cut in one piece. The opening for the curve should measure 1/2” wide.  Save the 1/2” wide die cut piece and keep it in tact to use later.

  5. 5.Spray the curve with brown paint.

  6. 6.When dry, stick the die cut 1/2” wide curve in place to cover the brown paint.  Protect the right side of the curve from accidental overspray.  Position the single die cut filigree piece (not the stencil) on the left side of the curve.   Spray a generous area around it with turquoise.  Move the die cut to the second and then third position, spraying each.  Go back and fill in the entire remainder of the left side with turquoise paint.  Avoid painting the white filigrees.  Let dry completely.

  7. 7.Protect the left side of the wrap.  Position the filigree stencils as pictured in the sketch.  Note that the top half of the wrap and bottom mirror each other so the stencils have to be flipped over to be reused.  Spray the stencil with turquoise then dust it lightly in places with brown for accents.  Be sure there is no wet paint on the stencil when you flip it.  Complete all the filigrees in this way.  Let dry completely.

  8. 8.Position the small accent stencil so it straddles the first curve.  Paint it turquoise followed by brown as you did the filigrees.  Repeat on the other two curves. 

divaonline

Which Sewing Machine To Buy

What Sewing Patterns Don’t Tell You

How To Sew A Perfect Narrow Hem and A Hand Rolled Hem

The Best Affordable 5 Thread Serger Sewing Machine

divaonline

Which Digital Stencil Cutter To Buy?

Stencil Making Tools And Materialshttp://www.infobarrel.com/Stencil_Making_Tools_And_Materialshttp://www.infobarrel.com/Stencil_Making_Tools_And_Materialshttp://www.infobarrel.com/Stencil_Making_Tools_And_Materialsshapeimage_9_link_0shapeimage_9_link_1

Make Stencils With Your Computer

Word Art Stencils

THIS SITE IS BEST VIEWED WITH FIREFOX Download it now.http://www.mozilla.org/en-US/firefox/new/